Electrical accessories & LED drivers

The 3W LED Emergency Beacon has a highly waterproof casing and an IP65 protection rating, making it highly resistant to the elements, so it can be installed both indoors and outdoors. It has protective fuses and a battery with a runtime of up to 3 hours. Its integrated LEDs provide high efficiency, durability and excellent performance.

The LED Emergency Beacon provides both permanent and non-permanent lighting. This emergency light is pre-configured as a non-permanent light. By changing the position of the PCB connector, you can select the permanent operating mode.

The 3W LED Emergency Beacon is the most practical, economical and simple solution in the event of a power failure. It is easy to install on both walls and ceilings. It can also be surface-mounted, thanks to the part it incorporates that adapts to the luminaire.

* LED operating indicator.

* For the emergency lighting to work properly, you need to connect the battery pre-wiring.

Kanlux SLICK JQ is a motion sensor with a maximum motion detection range of 12 m. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Waterproof junction box with 4 IP68 inputs, miidex 7232

Electrical cable diameter 9 to 12 mm

Dimensions (L x W x H): 145 x 110 x 56 mm

Voltage: 16A / 450V max

IP68 protection

Connector: 3-wire Flexible, rigid, semi-rigid cable

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.

With a simple movement of the hand at a distance of 0 to 3.5 cm from the sensor, you can switch any light on or off. It has a power rating of up to 300W, so you can switch a single bulb or several downlights in a corridor on and off. The light will remain on until another hand movement is detected. The sensor's angle of detection is 90º, making it easy to switch on from any position.

This short-range, non-contact sensor switch is a perfect solution for areas with high pedestrian traffic, to prevent the transmission of bacteria and viruses through contact.

Light up your home discreetly with the Short Range Contactless Sensor Switch for Motion Lighting

A highly sensitive microwave sensor with adjustable parameters (illumination time, activation threshold and detection distance).

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.

The Contactless Detection Switch for Cabinet Doors allows any light in a cabinet to be switched on without the need for a wall switch.

Features of the Contactless Detection Switch for Cabinet Doors

The Contactless Detection Switch for Cabinet Doors detects when the door is opened by switching on the light to which it is connected. This light will remain on until the sensor detects that the door is closed, at which point the light will be switched off. The sensor's angle of detection is 90°.

Applications of the Contactless Detection Switch for Cabinet Doors

The Contactless Detection Switch for Cabinet Doors is the perfect solution for illuminating your tool cabinets, wardrobes and kitchen cupboards, making it easier to see and select what you need.

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.