Electrical accessories & LED drivers

• Dimensions:
• Height (mm): 80
• Width (mm) : 66
• Length (mm) : 45

Kanlux ROLF JQ is a microwave motion sensor. The maximum horizontal operating angle of the sensor is 360 degrees. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Kanlux ROLF JQ is a microwave motion sensor. The maximum horizontal operating angle of the sensor is 360 degrees. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

• Dimensions:
• Height (mm): 200
• Width (mm) : 112
• Length (mm): 112
• Number of modules: 4

DB series switching devices, which meet the requirements for resistance to embers at 650°C, may only be used on non-combustible surfaces (e.g. solid, solid walls made of non-combustible materials). They may not be used on flammable surfaces (e.g. plasterboard, wood, etc.), hollow walls or electrical conduits.

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.

The Kanlux ADI electronic power supply unit, with a maximum permissible case temperature of 75°C and current stabilisation of 350mA DC, is equipped with short-circuit and overload protection, as well as thermal protection that shuts down the power supply unit once the temperature exceeds 110°C.

• Dimensions: Ø54.5 x 21.5 mm
• Voltage: 220/240V AC
• IP protection: 20

Kanlux DimGO is a dimmer suitable for LED light sources. It can be used to control the luminous flux of LED light sources. The prerequisite for using the Kanlux DimGO is a power supply suitable for the "trailing/leadership edge" control method.

Last units on special offer

Warning! product guaranteed 3 months, no refund or exchange.

• Dimensions:
• Height (mm): 220
• Width (mm) : 102
• Length (mm): 210
• Number of modules: 6

KDB series switchgear, which meets the requirements for resistance to embers at 650°C, may only be used on non-combustible surfaces (e.g. solid, solid walls made of non-combustible materials). They may not be used on flammable surfaces (e.g. plasterboard, wood, etc.), hollow walls or electrical conduits.

• Dimensions:
• Height (mm): 160
• Width (mm) : 65
• Length (mm): 160
• Number of modules: 8

DB series switching devices, which meet the requirements for resistance to embers at 650°C, may only be used on non-combustible surfaces (e.g. solid, solid walls made of non-combustible materials). They may not be used on flammable surfaces (e.g. plasterboard, wood, etc.), hollow walls or electrical conduits.

Kanlux MERGE JQ is a motion sensor with a maximum motion detection range of 5 m. The maximum horizontal operating angle of the sensor is 360 degrees. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Last units on sale

Attention! product guaranteed 3 months, neither recovered nor exchanged.

The Kanlux MERGE MW sensor offers an aesthetic and practical solution. It has a maximum motion detection range of 9 m. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Last units on sale

Attention! product guaranteed 3 months, neither recovered nor exchanged.

• Dimensions:
• Height (mm): 200
• Width (mm) : 95
• Length (mm): 147
• Number of modules: 6

DB series switching devices, which meet the requirements for resistance to embers at 650°C, may only be used on non-combustible surfaces (e.g. solid, solid walls made of non-combustible materials). They may not be used on flammable surfaces (e.g. plasterboard, wood, etc.), hollow walls or electrical conduits.

• Dimensions:
• Height (mm): 204
• Width (mm): 102
• Length (mm): 194
• Number of modules: 6

Series KDB switchgear, which meets the requirements for resistance to embers at 650°C, may only be used on non-combustible surfaces (e.g. solid, solid walls made of non-combustible materials). They may not be used on flammable surfaces (e.g. plasterboard, wood, etc.), hollow walls or electrical conduits.

• Dimensions:
• Height (mm): 130
• Width (mm) : 60
• Length (mm): 86
• Number of modules: 4

DB series switching devices, which meet the requirements for resistance to embers at 650°C, may only be used on non-combustible surfaces (e.g. solid, solid walls made of non-combustible materials). They may not be used on flammable surfaces (e.g. plasterboard, wood, etc.), hollow walls or electrical conduits.

Kanlux MERGE JQ is a motion sensor with a maximum motion detection range of 5 m. The maximum horizontal operating angle of the sensor is 360 degrees. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Kanlux MERGE ADJ is an infra-red motion detector which detects over a maximum range of 5m. It also detects 360°. The MERGE ADJ detector's settings are easily accessible and do not need to be dismantled.

Kanlux ROLF JQ is a microwave motion sensor. The maximum horizontal operating angle of the sensor is 360 degrees. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Kanlux ZONA JQ is a motion sensor with a maximum motion detection range of 10 m. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Kanlux ZONA JQ is a motion sensor with a maximum motion detection range of 10 m. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Kanlux ZONA FLAT is an infra-red motion detector which detects over a maximum range of 8m. It also detects 360°. On the ZONA FLAT, you can also adjust the time delay from 10s to 15min, and set the light detection threshold.

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.