Electrical accessories & LED drivers

The 3W LED Emergency Beacon has a highly waterproof casing and an IP65 protection rating, making it highly resistant to the elements, so it can be installed both indoors and outdoors. It has protective fuses and a battery with a runtime of up to 3 hours. Its integrated LEDs provide high efficiency, durability and excellent performance.

The LED Emergency Beacon provides both permanent and non-permanent lighting. This emergency light is pre-configured as a non-permanent light. By changing the position of the PCB connector, you can select the permanent operating mode.

The 3W LED Emergency Beacon is the most practical, economical and simple solution in the event of a power failure. It is easy to install on both walls and ceilings. It can also be surface-mounted, thanks to the part it incorporates that adapts to the luminaire.

* LED operating indicator.

* For the emergency lighting to work properly, you need to connect the battery pre-wiring.

A dimmable LED bulb requires a carefully designed dimmer.

Connecting an LED bulb to a traditional dimmer often results in irregular operation, flickering light and a high risk of burning out the bulb.

Our button dimmer, on the other hand, has been designed for all types of bulb: traditional filament, energy-saving, dimmable and dimmable LED.

Designed and produced 100% in Italy, the LED dimmer with knob will allow you to regulate the intensity of light more comfortably and safely.

Download installation instructions (412.04k)

• Dimensions Ø 0.5 to 2.5 mm² wires

• Dimensions (L x W x H): 17.5 x 11 x 8 mm

• Voltage: 24A / 250V max

• IP20 protection

  • Connector: 2 rigid wires

• Packaging: Box of 100

• Dimensions Ø 0.5 to 4.5 mm² wires

• Dimensions ( Ø x L): Ø25 x 84 mm

• Voltage: 16A / 250V max

• IP68 protection

  • • Connector: 3 wires

• Cross-sectional area: 0.5 to 2.5 mm²

• Dimensions (L x W): 175 x 31 mm

Dimensions (L x W): 160 x 28 mm

Compatible with: GU10 - GZ10 230V CL1

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.

Kanlux SLICK JQ is a motion sensor with a maximum motion detection range of 12 m. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

6X0.22²

You can use this cable to connect RGB+ LED stripsCCT together. This is ideal when you want to connect several LED strips that are a long way apart to the same controller.

• Electric cable diameter from 9 to 12 mm

• Dimensions ( L x W x H): 130 x 105 x 37 mm

• Voltage: 16A / 450V max

• IP68 protection

  • • Connector: 3-wire Flexible, rigid, semi-rigid cable

Sometimes small ideas make all the difference: this is the case with the Schuko plug with pull-out ring, which makes it easier and safer to connect and disconnect the plug from a socket.

What's more, the Schuko comfort plug can be fitted and removed with just one screw, simplifying wiring operations.

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.

Waterproof junction box with 4 IP68 inputs, miidex 7232

Electrical cable diameter 9 to 12 mm

Dimensions (L x W x H): 145 x 110 x 56 mm

Voltage: 16A / 450V max

IP68 protection

Connector: 3-wire Flexible, rigid, semi-rigid cable

This is a resistor to be connected in parallel with an energy-saving bulb or LED to obtain dimming.

Be careful, this resistor heats up, so keep it away from plastic materials and it does not work with all dimmers on the market.

"Supplied without connector

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current to light up the LED chips.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.

With a simple movement of the hand at a distance of 0 to 3.5 cm from the sensor, you can switch any light on or off. It has a power rating of up to 300W, so you can switch a single bulb or several downlights in a corridor on and off. The light will remain on until another hand movement is detected. The sensor's angle of detection is 90º, making it easy to switch on from any position.

This short-range, non-contact sensor switch is a perfect solution for areas with high pedestrian traffic, to prevent the transmission of bacteria and viruses through contact.

Light up your home discreetly with the Short Range Contactless Sensor Switch for Motion Lighting

5X0.22²

You can use this cable to connect RGB+W LED strips together. This is ideal when you want to connect several LED strips that are a long way apart to the same controller.

The 3-hole metal rose kit can be used to assemble a wall or ceiling lamp with three light sources.
Metal is a durable material and can be placed in a wide range of environments, whatever their style: whether minimal, Scandinavian, industrial or classic, you'll find the metal finish to suit you!

• Finish: Black

• Dimensions (Ø x H): Ø 120 x 10 mm

• Dimensions:
• Width (mm): 19
• Length (mm) : 20000

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.

Fitting: E27

• Dimensions (Ø x H): Ø 34 x 50 mm

• Characteristics: Adapter to GU10

ALER MINI is an infrared motion detector with an attractive, minimalist design. It has a horizontal detection range of 140° and a vertical range of 45°, and thanks to its tilting mechanism (vertical 45°, horizontal 90°) it can be adapted to suit all your needs. Thanks to its waterproof rating (IP44), this detector can be installed in places exposed to the elements.

Kanlux MERGE JQ is a motion sensor with a maximum motion detection range of 5 m. The maximum horizontal operating angle of the sensor is 360 degrees. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Kanlux MERGE ADJ is an infra-red motion detector which detects over a maximum range of 5m. It also detects 360°. The MERGE ADJ detector's settings are easily accessible and do not need to be dismantled.

Kanlux ROLF JQ is a microwave motion sensor. The maximum horizontal operating angle of the sensor is 360 degrees. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Kanlux ZONA JQ is a motion sensor with a maximum motion detection range of 10 m. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Kanlux ZONA JQ is a motion sensor with a maximum motion detection range of 10 m. It is possible to set the lighting time and the level of light intensity at which the sensor operates.

Kanlux ZONA FLAT is an infra-red motion detector which detects over a maximum range of 8m. It also detects 360°. On the ZONA FLAT, you can also adjust the time delay from 10s to 15min, and set the light detection threshold.

Kanlux AS-10 is a twilight detector. It is used to switch on and off the power circuits of the lighting system or other electrical receivers, depending on the level of natural light intensity (day/night).

• Fitting: E14

• Dimensions (Ø x H): Ø 33 x 43 mm

• Fitting: E27

• Dimensions (Ø x H): Ø 44 x 47 mm

• Fitting: E27

• Dimensions (Ø x H): Ø 40 x 47 mm

• Base: R7S

• Dimensions (L x W x H): Ø 15 x 16 x 40 mm

• (sold individually)

The Textile Electrical Cable is an electrical sheath with a cross-section of 1.5mm² made up of three pure copper multi-core cables with a diameter of 0.75mm² each, making it ideal for lighting installations. It has a textile coating available in different colours.

Combine it with the sockets, suspension cables and finials in the DIY collection. Decorate your rooms and create your own personalised lamps!

* Cable diameter: 6mm.

* Product made to your specifications, and therefore exempt from the right of withdrawal.

A highly sensitive microwave sensor with adjustable parameters (illumination time, activation threshold and detection distance).

Universal driver specially designed for Downlight, LED tiles and ceiling lights and other products that use a dimmable or non-dimmable LED driver.

An LED driver transforms the mains alternating current into direct current so that the LED chips can be lit.

To find out whether a driver will work with our luminaire, PCB or panel, you need to check the driver's output voltage and current.

ATTENTION you must consult the driver's output voltage and current.

Flat Electrical Cable Sheath 4X0.25Mm² For Rgb Led Ribbons - 500 Metres

Flat Electrical Cable Sheath 2X0.5Mm² For Single Colour Led Ribbons - 500 Metres